A review of doped lanthanum gallates as electrolytes for intermediate temperature solid oxides fuel cells: From materials processing to electrical and thermo-mechanical properties

AFM as an alternative for Young’s modulus determination in ceramic materials in elastic deformation regime

Anode-supported SOFC Operated Under Single-chamber Conditions at Intermediate Temperatures

Calculation of Young's Modulus Value by Means of AFM

scientific article published on 01 January 2011

Cation order enhancement in Sr2FeMoO6 by water-saturated hydrogen reduction

Contact Mechanics at Nanometric Scale Using Nanoindentation Technique for Brittle and Ductile Materials

Correlation between electrical and mechanical properties in La1−xSrxGa1−yMgyO3−δ ceramics used as electrolytes for solid oxide fuel cells

Corrigendum to: “Mechanical properties at the nanometric scale of GDC and YSZ used as electrolytes for solid oxide fuel cells” [Acta Materialia 58 (2010) 2504–2509]

scholarly article published in Acta Materialia

Corrosion induced degradation of textured YBCO under operation in high humidity conditions

Determination of hardness, Young's modulus and fracture toughness of lanthanum tungstates as novel proton conductors

Effective silver-assisted welding of YBCO blocks: mechanical versus electrical properties

Electrical and mechanical characterization by instrumented indentation technique of La0.85Sr0.15Ga0.8Mg0.2O3−δ electrolyte for SOFCs

Epitaxial Growth of SrTiO3 Films on Cube-Textured Cu-Clad Substrates by PLD at Low Temperature Under Reducing Atmosphere.

scientific article

Fracture micromechanisms and mechanical behavior of YBCO bulk superconductors at 77 and 300K

scholarly article by K. Konstantopoulou et al published September 2014 in Ceramics International

Hardness of FRHC-Cu Determined by Statistical Analysis

Idm@ti Network: An innovative proposal for improving teaching and learning in Spanish universities

scientific article

Influence of the Synthesis Route in Obtaining the Cubic or Tetragonal Copper Ferrite Phases

scientific article published on 18 June 2020

Low-grade MgO used to stabilize heavy metals in highly contaminated soils.

scientific article published in August 2004

Manufacturing of anode-supported tubular solid oxide fuel cells by a new shaping technique using aqueous gel-casting

Mechanical Characterisation at Nanometric Scale of a New Design of SOFCs

Mechanical properties at the nanometer scale of GDC and YSZ used as electrolytes for solid oxide fuel cells

Mechanical properties of highly textured porous Ni–YSZ and Co–YSZ cermets produced from directionally solidified eutectics

Nano-mechanical properties of silver-welded YBCO bulks

Nanohardness and Young’s modulus of YBCO samples textured by the Bridgman technique

Nanoindentation of Bridgman YBCO samples

Nanoindentation of multilayered epitaxial YBa2Cu3O7-δ thin films and coated conductors

Nanoindentation with spherical tips of single crystals of YBCO textured by the Bridgman technique: Determination of indentation stress–strain curves

Novel Procedures for the Microstructural Design of SOFC Materials

On–off magnetoresistive sensor based on screen-printed La2/3Sr1/3MnO3 manganite

Oxygenation kinetics of YBCO-TSMG samples using the nanoindentation technique

Performance and short-term stability of single-chamber solid oxide fuel cells based on La0.9Sr0.1Ga0.8Mg0.2O3−δ electrolyte

Performance of a novel type of electrolyte-supported solid oxide fuel cell with honeycomb structure

Processing of graded anode-supported micro-tubular SOFCs based on samaria-doped ceria via gel-casting and spray-coating

Reversible ferromagnetic switching in ZnO:(Co, Mn) powders

scholarly article in Physical Review B, vol. 75 no. 15, April 2007

Selection of materials with potential in sensible thermal energy storage

Short-term natural weathering of MSWI bottom ash as a function of particle size.

scientific article published in January 2003

Structural and magnetic properties of ZnO:TM (TM: Co, Mn) nanopowders

Study of the friction, adhesion and mechanical properties of single crystals, ceramics and ceramic coatings by AFM

Study of the mechanical properties of CeO2 layers with the nanoindentation technique

Using the recyclability index of materials as a tool for design for disassembly

scientific article published in 2004

Yield strength, shear stress and toughness of YBCO samples textured by Bridgman technique