3-D Printed Microwave Patch Antenna via Fused Deposition Method and Ultrasonic Wire Mesh Embedding Technique

3D Printed Electronics With High Performance, Multi-Layered Electrical Interconnect

3D Printing for the Rapid Prototyping of Structural Electronics

article

3D Printing multifunctionality: structures with electronics

3D printed capacitive sensors

3D printed multilayer microstrip line structure with vertical transition toward integrated systems

A Hardware Platform for Tuning of MEMS Devices Using Closed-Loop Frequency Response

A novel floating gate circuit family with subthreshold voltage swing for ultra-low power operation

A study to detect a material deposition status in fused deposition modeling technology

Adaptive subthreshold switched capacitor voltage boost for thermoelectric generation

Anisotropy of thermal conductivity in 3D printed polymer matrix composites for space based cube satellites

Augmenting Computer-Aided Design Software With Multi-Functional Capabilities to Automate Multi-Process Additive Manufacturing

Comparison of stress concentrator fabrication for 3D printed polymeric izod impact test specimens

Conductive polymer-coated threads as electrical interconnects in e-textiles

article by Michael D. Irwin et al published October 2011 in Fibers and Polymers

Cooperative Tool Path Planning for Wire Embedding on Additively Manufactured Curved Surfaces Using Robot Kinematics

article published in 2015

Delay Insensitive logic with increased fault tolerance and optimized for subthreshold operation

Delay testing of partially depleted silicon-on-insulator (PD-SOI) circuits

Design of a Prototype for a Novel Rehabilitative Device for Hearing Preservation through Feedback and Control

Development of a Fused Deposition Modeling System for Low Melting Temperature Metal Alloys

article

Electromagnetic materials of artificially controlled properties for 3D printing applications

Encapsulated Copper Wire and Copper Mesh Capacitive Sensing for 3-D Printing Applications

scholarly article by Corey Shemelya et al published February 2015 in IEEE Sensors Journal

Expanding the applicability of FDM-type technologies through materials development

article

Fabricating patch antennas within complex dielectric structures through multi-process 3D printing

Fabrication of barium titanate by binder jetting additive manufacturing technology

scholarly article by S.M. Gaytan et al published June 2015 in Ceramics International

Fabrication of microwave patch antenna using additive manufacturing technique

Failure Investigation of Direct Write Pen Tips

Hardware Platforms for MEMS Gyroscope Tuning Based on Evolutionary Computation Using Open-Loop and Closed-Loop Frequency Response

Heavy Ion Characterization of a Radiation Hardened Flip-Flop Optimized for Subthreshold Operation

Integrating stereolithography and direct print technologies for 3D structural electronics fabrication

Laser curing of silver-based conductive inks for in situ 3D structural electronics fabrication in stereolithography

Mechanical, Electromagnetic, and X-ray Shielding Characterization of a 3D Printable Tungsten–Polycarbonate Polymer Matrix Composite for Space-Based Applications

scholarly article by Corey M. Shemelya et al published 6 March 2015 in Journal of Electronic Materials

Micron-Level Layer-Wise Surface Profilometry to Detect Porosity Defects in Powder Bed Fusion of Inconel 718

Microstructural and Process Characterization of Conductive Traces Printed from Ag Particulate Inks

scientific article published on 26 May 2011

Microstructural characterization of electrically failed conductive traces printed from Ag nanoparticle inks

Miniaturized self-adaptive tuning of MEMS gyroscope for space

Multi-functional 3D printed and embedded sensors for satellite qualification structures

Multi-layer archimedean spiral antenna fabricated using polymer extrusion 3D printing

Multi-layer off-axis patch antennas fabricated using polymer extrusion 3D printing

Multi-material microstereolithography

Multiprocess 3D printing for increasing component functionality

scientific article published on 29 September 2016

Novel ABS-based binary and ternary polymer blends for material extrusion 3D printing

Ohmic Curing of Printed Silver Conductive Traces

article published in 2012

Ohmic Curing of Three-Dimensional Printed Silver Interconnects for Structural Electronics

Printed electronic processes for flexible hybrid circuits and antennas

article

Radiation hardened Flip-Flop design for super and sub threshold voltage operation

Radiation hardened level shifter for sub to superthreshold voltage translation

Reductions of instantaneous power by ripple scan clocking

Robust Ultra-Low Power Subthreshold Logic Flip-Flop Design for Reconfigurable Architectures

scholarly article published September 2006

Slice overlap-detection algorithm for process planning in multiple-material stereolithography

SnO 2 -based memristors and the potential synergies of integrating memristors with MEMS

Spatial Frequency Analysis for Improved Quality in Big Area Additive Manufacturing (BAAM)

The Mechanical Properties of Fiber Metal Laminates Based on 3D Printed Composites

scientific article published on 21 November 2020

The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting

Torsion analysis of the anisotropic behavior of FDM technology

Ultra Low Voltage Level Shifters to Interface Sub and Super Threshold Reconfigurable Logic Cells

Unobtrusive In Situ Diagnostics of Filament-Fed Material Extrusion Additive Manufacturing

Very low voltage testing of SOI integrated circuits

article